1° Forum di Astronomia Amatoriale Italiano

http://forum.10micron.eu/viewtopic.php?t=180

Cari saluti,
Danilo Pivato

_________________



Latest New: https://www.danilopivato.com/introduction/latest_news/latest_news.html

Potresti riportare qua il changelog per chi non ha accesso a quel forum?

_________________
Salvatore Iovene, http://www.iovene.com/
10Micron GM2000 QCI, GSO RC8 con APCCD67, CCD Moravian G2-1600FW (filtri LRGBHa), TS OAG27, Lodestar.

Quoto.

_________________
Strumentazione
Newton TS 6" - RC 8 GSO - MN 180/1000 Skywatcher - Zen schmidt camera 250 F/3
Simak 240/1310 Zen - Konus Vista arancione (acro 80/400) - SolarAlpha 120
Vixen NEXSXD - iOptron G70
Canon 450D - Magzero 9- QHY8L- Lodestar II - Moravian G3 6300

-------------------------------------------------------------------------------
UPGRADE NOTES
-------------------------------------------------------------------------------

This file contains the release notes for each firmware upgrade.
Please read all notes down to the firmware version currently installed in your
mount.

WARNING: If you update to a 2.x version a mount with a 1.x firmware, all
position settings will be lost and you will have to start with a new alignment.

-------------------------------------------------------------------------------
Upgrade notes for GM QCI & HPSseries mounts- software version 2.8.19
-------------------------------------------------------------------------------

Now the latitude and longitude fields in the menu Local Data->Site->Current
and in the menu Local Data->Site->Enter show the letters 'E', 'W', 'N', 'S'
instead of plus or minus.

-------------------------------------------------------------------------------
Upgrade notes for GM QCI & HPSseries mounts- software version 2.8.18
-------------------------------------------------------------------------------

GM4000QCI mount in 48V version is correctly identified in the startup display.

-------------------------------------------------------------------------------
Upgrade notes for GM QCI & HPSseries mounts- software version 2.8.17
-------------------------------------------------------------------------------

Now the mount support a "Remote assist" modality. To use it, you must contact
the customer support in advance. Then make sure that the mount is able to reach
the Internet using its LAN interface, and select from the menu
Settings->Network->Remote Assist.

-------------------------------------------------------------------------------
Upgrade notes for GM QCI & HPSseries mounts- software version 2.8.16
-------------------------------------------------------------------------------

Some minor bugs have been corrected.

-------------------------------------------------------------------------------
Upgrade notes for GM QCI & HPSseries mounts- software version 2.8.15
-------------------------------------------------------------------------------

For the GM1000HPS, GM2000HPS and GM4000HPS mounts the synchronization commands
(:CM, :CMR) have been updated to allow using the synchronization function to
input additional points for the pointing model.
This changes also the function of the long-enter press on the keypad.
To set the synchronization function use the function in the menu
Drive->Sync refines.

-------------------------------------------------------------------------------
Upgrade notes for GM QCI & HPSseries mounts- software version 2.8.14
-------------------------------------------------------------------------------

This version supports the updated altitude and altazimuth adjustment system
with the correct number of knob revolutions for adjusting the polar axis in
the menu Alignment->Align Info in for GM2000HPS mounts from S/N.20001011.

-------------------------------------------------------------------------------
Upgrade notes for GM QCI & HPSseries mounts- software version 2.8.13
-------------------------------------------------------------------------------

Now the user is forced to restart the 2-Stars or 3-Stars alignment after a
Polar Align or Ortho Align, as this is the correct thing to do to avoid
errors.

The "MANUAL MOVE" message when moving by hand has been removed.

-------------------------------------------------------------------------------
Upgrade notes for GM QCI & HPSseries mounts- software version 2.8.12
-------------------------------------------------------------------------------

The dome interface has been changed for better responsiveness. Tracking
parameters have been modified for improved tracking behaviour.

-------------------------------------------------------------------------------

_________________



Latest New: https://www.danilopivato.com/introduction/latest_news/latest_news.html

C'e' quslche novita' anche per la 4000? Anche vecchia di un annetto.
Ciao e grazie.

Edit: Gia risposto mentre scrivevo. Grazie

_________________
ES ULD 16' Gen II
Bresser Messier 6'
Vixen A70Lf su Porta Mini
APM XWA 100° 20, 13, 9, 7, 5, 3.5
ES 82° 30, 18, 11
PLOSSL Vixen 20 6,3 Tecnosky 9
Kellner Bresser 25 9
ES UHC OIII e ND variabile da 2"
Radiant SQML GSO Coma Corr.

Rispolvero il post ... sembra che finalmente stiano lavorando al driver ascom ufficiale .... da parte nostra quello di gialuca testa è ottimo, ma limitato alle funzioni che ci interessavano (comunque tante).

Speriamo che qualcosa si muova secondo me qualcosa di strano nell'aria c'e' almeno dal punto di vista del software.

Carlo

_________________
Carlo Martinelli - IW3GIK

Osservatorio: StarNavigator Astronomical Observatory (Masi-PD)
Montatura GM2000 QCI 10 Micron Comec Tec.;
Telescopi: Meade LXD55 S/N 1016/254 Schmidt/Newton F4; Takahashi FS102 820/102 F8 612/F6; Takahashi FS60C 355/60/ f5.9 - 264/F4.4; TS 60/228 F3.8; Celestron C11 Carbon 2800/F10 1764/F6.3; OTA MTO 1000/100 F10 SkyQualityMeter: SQM-L / SQM-LE Wheather: AAG-CloudWatcher LaCross WS55 SkyCam: AllSkyCam-MoonGlow Tec. Observatory Automation System :Voyager / Viking